Fanuc

Fanuc alarm: 245 - T-CODE NOT ALLOWED IN THIS BLOCK

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
245 - T-CODE NOT ALLOWED IN THIS BLOCK

Alarm Description

One of the G codes, G50, G10, and G04, which cannot be specified in the same block as a T code, was specified with a T code.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 245 - T-CODE NOT ALLOWED IN THIS BLOCK) error message below.

Fanuc alarm: 244 - P/S ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
244 - P/S ALARM

Alarm Description

In the skip function activated by the torque limit signal, the number of accumulated erroneous pulses exceed 32767 before the signal was input. Therefore, the pulses cannot be corrected with one distribution. Change the conditions, such as feed rates along axes and torque limit, and try again.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 244 - P/S ALARM) error message below.

Fanuc alarm: 243 - OVER TOLERANCE OF END POINT

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
243 - OVER TOLERANCE OF END POINT

Alarm Description

The end point is not on the involute curve which includes the start point and thus falls outside the range specified with parameter No. 5610.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 243 - OVER TOLERANCE OF END POINT ) error message below.

Fanuc alarm: 242 - ILLEGAL COMMAND IN G02.2/G03.2

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
242 - ILLEGAL COMMAND IN G02.2/G03.2

Alarm Description

An invalid value has been specified for involute interpolation. The start or end point is within the basic circle. I, J, K, or R is set to 0. The number of rotations between the start of the involute curve and the start or end point exceeds 100.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 242 - ILLEGAL COMMAND IN G02.2/G03.2 ) error message below.

Fanuc alarm: 241 - ILLEGAL FORMAT IN G02.2/G03.2

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
241 - ILLEGAL FORMAT IN G02.2/G03.2

Alarm Description

The end point, I, J, K, or R is missing from a command for involute interpolation.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 241 - ILLEGAL FORMAT IN G02.2/G03.2 ) error message below.

Fanuc alarm: 240 - BP/S ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
240 - BP/S ALARM

Alarm Description

Background editing was performed during MDI operation.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 240 - BP/S ALARM) error message below.

Fanuc alarm: 239 - BP/S ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
239 - BP/S ALARM

Alarm Description

While punching was being performed with the function for controlling external I/O units ,background editing was performed.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 239 - BP/S ALARM) error message below.

Fanuc alarm: 233 - DEVICE BUSY or P/S ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
233 - DEVICE BUSY or P/S ALARM

Alarm Description

When an attempt was made to use a unit such as that connected via the RS232C interface other users were using it. Or In the skip function activated by the torque limit signal, the number of
accumulated erroneous pulses exceed 32767 before the signal was
input. Therefore, the pulses cannot be corrected with one distribution.
Change the conditions, such as federates along axes and torque
limit, and try again.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 233 - DEVICE BUSY or P/S ALARM) error message below.

Fanuc alarm: 232 - TOO MANY HELICAL AXIS COMMANDS

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
232 - TOO MANY HELICAL AXIS COMMANDS

Alarm Description

Three or more axes (in the normal direction control mode two or more axes) were specified as helical axes in the helical interpolation mode.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 232 - TOO MANY HELICAL AXIS COMMANDS ) error message below.

Fanuc alarm: 231 - ILLEGAL FORMAT IN G10 OR L50

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, 0/00/0-mate, 0i
231 - ILLEGAL FORMAT IN G10 OR L50

Alarm Description

Any of the following errors occurred in the specified format at the programmable parameter input. 1) Address N or R was not entered. 2) A number not specified for a parameter was entered. 3) The axis number was too large. 4) An axis number was not specified in the axis-type parameter. 5) An axis number was specified in the parameter which is not an axis type. Correct the program. 6) In the locked state set by the password function, an attempt was made to set bit 4 (NE9) of parameter No. 3204 to 0 or change the contents of parameter No. 3210. 7) An attempt was made to change a program encryption parameter (parameter No. 3220 to 3223).

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 231 - ILLEGAL FORMAT IN G10 OR L50) error message below.

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer